-- *********************************************************************
-- CISCO-ISCSI-MIB.my: iSCSI (SCSI over TCP) Mib
--
-- October 2002, Vinay Gaonkar
--
-- Copyright (c) 2002 by cisco Systems, Inc.
-- All rights reserved.
--
-- *********************************************************************
-- This MIB module is based on the Internet Draft
-- <draft-ietf-ips-iscsi-mib-05.txt>. In terms of object syntax
-- and semantics, the content of this Cisco MIB is the same as
-- the corresponding Internet Draft revision. This Cisco MIB was
-- created due to the "subject to change" nature of Internet Drafts.
-- This Cisco MIB may later be deprecated, and the stable RFC, which
-- may replace the Internet Draft, may be implemented in its place.CISCO-ISCSI-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,OBJECT-IDENTITY,NOTIFICATION-TYPE,Unsigned32,Counter32,Counter64,Gauge32FROM SNMPv2-SMI
TEXTUAL-CONVENTION,TruthValue,RowPointer,TimeStamp,RowStatus,AutonomousTypeFROM SNMPv2-TC
MODULE-COMPLIANCE,OBJECT-GROUP,NOTIFICATION-GROUP
FROM SNMPv2-CONF
SnmpAdminStringFROM SNMP-FRAMEWORK-MIB -- RFC 2571InetAddressType,InetAddressFROM INET-ADDRESS-MIB -- RFC 3291ciscoExperiment
FROM CISCO-SMI
;ciscoIscsiModule MODULE-IDENTITYLAST-UPDATED"200210050000Z"ORGANIZATION"IETF IPS Working Group"CONTACT-INFO" Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553 -NETS
E-mail: cs-san@cisco.com"DESCRIPTION"The iSCSI Protocol MIB module."REVISION"200210050000Z"DESCRIPTION"Initial revision published of this MIB module."::={ ciscoExperiment 94}cIscsiObjects OBJECTIDENTIFIER::={ ciscoIscsiModule 1}cIscsiNotifications OBJECTIDENTIFIER::={ ciscoIscsiModule 2}cIscsiConformance OBJECTIDENTIFIER::={ ciscoIscsiModule 3}
-- Textual ConventionsCIscsiTransportProtocols ::=TEXTUAL-CONVENTIONDISPLAY-HINT"d"STATUScurrentDESCRIPTION"This data type is used to define the transport
protocols that will carry iSCSI PDUs."REFERENCE"RFC791, RFC1700
The presently known, officially delegated numbers
can be found at:
http://www.iana.org/assignments/protocol-numbers"SYNTAXUnsigned32(0..255)CIscsiDigestMethod ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"This data type represents the methods possible
for digest negotiation.
none - a placeholder for a secondary digest method
that means only the primary method can be
used.
other - a digest method other than those defined below;
noDigest - does not support digests (will operate without
a digest (NOTE: implementations MUST support
digests to be compliant with the iSCSI RFC);
CRC32c - require a CRC32C digest."SYNTAXINTEGER{none(1),other(2),noDigest(3),
crc32c(4)}cIscsiDescriptors OBJECTIDENTIFIER::={ cIscsiObjects 1}cIscsiHeaderIntegrityTypes OBJECTIDENTIFIER::={ cIscsiDescriptors 1}cIscsiHdrIntegrityNone OBJECT-IDENTITYSTATUScurrentDESCRIPTION"The authoritative identifier when no integrity scheme (for
either the header or data) is being used."REFERENCE"iSCSI Protocol Specification."::={ cIscsiHeaderIntegrityTypes 1}cIscsiHdrIntegrityCrc32c OBJECT-IDENTITYSTATUScurrentDESCRIPTION"The authoritative identifier when the integrity scheme (for
either the header or data) is CRC-32c."REFERENCE"iSCSI Protocol Specification."::={ cIscsiHeaderIntegrityTypes 2}cIscsiDataIntegrityTypes OBJECTIDENTIFIER::={ cIscsiDescriptors 2}cIscsiDataIntegrityNone OBJECT-IDENTITYSTATUScurrentDESCRIPTION
"The authoritative identifier when no integrity scheme (for
either the header or data) is being used."REFERENCE"iSCSI Protocol Specification."::={ cIscsiDataIntegrityTypes 1}cIscsiDataIntegrityCrc32c OBJECT-IDENTITYSTATUScurrentDESCRIPTION"The authoritative identifier when the integrity scheme (for
either the header or data) is CRC-32c."REFERENCE"iSCSI Protocol Specification."::={ cIscsiDataIntegrityTypes 2}cIscsiInstance OBJECTIDENTIFIER::={ cIscsiObjects 2}-- Instance Attributes TablecIscsiInstanceAttributesTable OBJECT-TYPESYNTAXSEQUENCEOF CIscsiInstanceAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of iSCSI instances present on the system."::={ cIscsiInstance 1}cIscsiInstanceAttributesEntry OBJECT-TYPESYNTAX CIscsiInstanceAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry (row) containing management information applicable
to a particular iSCSI instance."INDEX{ cIscsiInstIndex }
::={ cIscsiInstanceAttributesTable 1}
CIscsiInstanceAttributesEntry ::=SEQUENCE{
cIscsiInstIndex Unsigned32,
cIscsiInstDescr SnmpAdminString,
cIscsiInstVersionMin Unsigned32,
cIscsiInstVersionMax Unsigned32,
cIscsiInstVendorID SnmpAdminString,
cIscsiInstVendorVersion SnmpAdminString,
cIscsiInstPortalNumber Unsigned32,
cIscsiInstNodeNumber Unsigned32,
cIscsiInstSessionNumber Unsigned32,
cIscsiInstSsnFailures Counter32,
cIscsiInstLastSsnFailureType AutonomousType,
cIscsiInstLastSsnRmtNodeName SnmpAdminString}cIscsiInstIndex OBJECT-TYPESYNTAXUnsigned32(1..4294967295)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An arbitrary integer used to uniquely identify a particular
ISCSI instance."
::={ cIscsiInstanceAttributesEntry 1}cIscsiInstDescr OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"An octet string, determined by the implementation to describe
the iSCSI instance. When only a single instance is present, this
object may be set to the zero-length string; with multiple
iSCSI instances, it may be used in an implementation-dependent
manner to describe the purpose of the respective instance."::={ cIscsiInstanceAttributesEntry 2}cIscsiInstVersionMin OBJECT-TYPESYNTAXUnsigned32(0..255)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Minimum version number of the iSCSI specification supported by
this instance."::={ cIscsiInstanceAttributesEntry 3}cIscsiInstVersionMax OBJECT-TYPESYNTAXUnsigned32(0..255)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Maximum version number of the iSCSI specification supported
by this instance."::={ cIscsiInstanceAttributesEntry 4}cIscsiInstVendorID OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"An octet string describing the manufacturer of the
implementation of this instance."::={ cIscsiInstanceAttributesEntry 5}cIscsiInstVendorVersion OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"An octet string set by the manufacturer describing the version
of the implementation of this instance. The format of this
string is determined solely by the manufacturer, and is for
informational purposes only. It is unrelated to the iSCSI
specification version numbers."::={ cIscsiInstanceAttributesEntry 6}cIscsiInstPortalNumber OBJECT-TYPESYNTAXUnsigned32(1..4294967295)UNITS"transport endpoints"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"The number of rows in the cIscsiPortalAttributesTable
which are currently associated with this iSCSI instance."::={ cIscsiInstanceAttributesEntry 7}cIscsiInstNodeNumber OBJECT-TYPESYNTAXUnsigned32(1..4294967295)UNITS"Internet Network Addresses"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of rows in the cIscsiNodeAttributesTable which are
currently associated with this iSCSI instance."::={ cIscsiInstanceAttributesEntry 8}cIscsiInstSessionNumber OBJECT-TYPESYNTAXUnsigned32(1..4294967295)UNITS"sessions"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of rows in the cIscsiSessionAttributesTable which
are currently associated with this iSCSI instance."::={ cIscsiInstanceAttributesEntry 9}cIscsiInstSsnFailures OBJECT-TYPESYNTAXCounter32UNITS"sessions"
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object counts the number of times a session belonging to
this instance has been failed."::={ cIscsiInstanceAttributesEntry 10}cIscsiInstLastSsnFailureType OBJECT-TYPESYNTAXAutonomousTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The counter object in the cIscsiInstSsnErrorStatsTable that was
incremented when the last session failure occurred.
If the reason for failure is not found in the
cIscsiInstSsnErrorStatsTable, the value { 0.0 } is used
instead."::={ cIscsiInstanceAttributesEntry 11}cIscsiInstLastSsnRmtNodeName OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"An octet string describing the name of the remote node from
the failed session."::={ cIscsiInstanceAttributesEntry 12}-- Instance Session Failure Stats TablecIscsiInstanceSsnErrorStatsTable OBJECT-TYPESYNTAXSEQUENCEOF CIscsiInstanceSsnErrorStatsEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"A list of error types that will cause a session failure."::={ cIscsiInstance 2}cIscsiInstanceSsnErrorStatsEntry OBJECT-TYPESYNTAX CIscsiInstanceSsnErrorStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry (row) containing management information applicable
to a particular iSCSI instance."AUGMENTS{ cIscsiInstanceAttributesEntry }
::={ cIscsiInstanceSsnErrorStatsTable 1}
CIscsiInstanceSsnErrorStatsEntry ::=SEQUENCE{
cIscsiInstSsnDigestErrors Counter32,
cIscsiInstSsnCxnTimeoutErrors Counter32,
cIscsiInstSsnFormatErrors Counter32}cIscsiInstSsnDigestErrors OBJECT-TYPESYNTAXCounter32UNITS"sessions"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of sessions which were failed due to receipt of a PDU
containing header or data digest errors."::={ cIscsiInstanceSsnErrorStatsEntry 1}
cIscsiInstSsnCxnTimeoutErrors OBJECT-TYPESYNTAXCounter32UNITS"sessions"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of sessions which were failed due to a sequence
exceeding a time limit."::={ cIscsiInstanceSsnErrorStatsEntry 2}cIscsiInstSsnFormatErrors OBJECT-TYPESYNTAXCounter32UNITS"sessions"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of sessions which were failed due to receipt of a PDU
which contained a format error."::={ cIscsiInstanceSsnErrorStatsEntry 3}--cIscsiPortal OBJECTIDENTIFIER::={ cIscsiObjects 3}-- Portal Attributes TablecIscsiPortalAttributesTable OBJECT-TYPESYNTAXSEQUENCEOF CIscsiPortalAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of transport endpoints (using TCP or another transport
protocol) used by this iSCSI instance. An iSCSI instance may
use a portal to listen for incoming connections to its targets,
to initiate connections to other targets, or both."::={ cIscsiPortal 1}cIscsiPortalAttributesEntry OBJECT-TYPESYNTAX CIscsiPortalAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry (row) containing management information applicable
to a particular portal instance."INDEX{ cIscsiInstIndex, cIscsiPortalIndex }
::={ cIscsiPortalAttributesTable 1}
CIscsiPortalAttributesEntry ::=SEQUENCE{
cIscsiPortalIndex Unsigned32,
cIscsiPortalRowStatus RowStatus,
cIscsiPortalRoles BITS,
cIscsiPortalAddrType InetAddressType,
cIscsiPortalAddr InetAddress,
cIscsiPortalProtocol CIscsiTransportProtocols,
cIscsiPortalMaxRecvDataSegLength Unsigned32,
cIscsiPortalPrimaryHdrDigest CIscsiDigestMethod,
cIscsiPortalPrimaryDataDigest CIscsiDigestMethod,
cIscsiPortalSecondaryHdrDigest CIscsiDigestMethod,
cIscsiPortalSecondaryDataDigest CIscsiDigestMethod,
cIscsiPortalRecvMarker TruthValue
}cIscsiPortalIndex OBJECT-TYPESYNTAXUnsigned32(1..4294967295)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An arbitrary integer used to uniquely identify a particular
transport endpoint within this iSCSI instance."::={ cIscsiPortalAttributesEntry 1}cIscsiPortalRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The status of the row."::={ cIscsiPortalAttributesEntry 2}cIscsiPortalRoles OBJECT-TYPESYNTAXBITS{targetTypePortal(0),initiatorTypePortal(1)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"A portal can operate in one or both of two roles: as a target
portal and/or an initiator portal.
When a new cIscsiPortalAttributesEntry is to be created, the
agent should use this object as a hint for the creation of a
new cIscsiTgtPortalAttributesEntry and/or
cIscsiIntrPortalAttributesEntry."::={ cIscsiPortalAttributesEntry 3}cIscsiPortalAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The type of Internet Network Address in the cIscsiPortalAddr."::={ cIscsiPortalAttributesEntry 4}cIscsiPortalAddr OBJECT-TYPESYNTAXInetAddressMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The portal's Internet Network Address."::={ cIscsiPortalAttributesEntry 5}cIscsiPortalProtocol OBJECT-TYPESYNTAX CIscsiTransportProtocols
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The portal's transport protocol."DEFVAL{6}-- TCP::={ cIscsiPortalAttributesEntry 6}cIscsiPortalMaxRecvDataSegLength OBJECT-TYPE
SYNTAXUnsigned32(512..16777215)MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The maximum PDU length this portal can receive. This may be
constrained by hardware characteristics and individual
implementations may chose not to allow this object to be
changed."DEFVAL{8192}
::={ cIscsiPortalAttributesEntry 7}cIscsiPortalPrimaryHdrDigest OBJECT-TYPESYNTAX CIscsiDigestMethod
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The preferred header digest for this portal."DEFVAL{ noDigest }
::={ cIscsiPortalAttributesEntry 8}cIscsiPortalPrimaryDataDigest OBJECT-TYPESYNTAX CIscsiDigestMethod
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"The preferred data digest method for this portal."DEFVAL{ noDigest }
::={ cIscsiPortalAttributesEntry 9}cIscsiPortalSecondaryHdrDigest OBJECT-TYPE
SYNTAX CIscsiDigestMethod
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"An alternate header digest preference for this portal."DEFVAL{ none }
::={ cIscsiPortalAttributesEntry 10}cIscsiPortalSecondaryDataDigest OBJECT-TYPESYNTAX CIscsiDigestMethod
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"An alternate data digest preference for this portal."DEFVAL{ none }
::={ cIscsiPortalAttributesEntry 11}cIscsiPortalRecvMarker OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object indicates whether or not this portal will
request markers in it's incoming data stream."::={ cIscsiPortalAttributesEntry 12}cIscsiTargetPortal OBJECTIDENTIFIER::={ cIscsiObjects 4}-- Target Portal Attributes TablecIscsiTgtPortalAttributesTable OBJECT-TYPESYNTAXSEQUENCEOF CIscsiTgtPortalAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of transport endpoints (using TCP or another transport
protocol) on which this iSCSI instance listens for incoming
connections to its targets."::={ cIscsiTargetPortal 1}cIscsiTgtPortalAttributesEntry OBJECT-TYPESYNTAX CIscsiTgtPortalAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry (row) containing management information applicable to
a particular portal instance that is used to listen for
incoming connections to local targets. This row is populated
for each cIscsiPortalAttributesEntry row that may be used as a
target portal."INDEX{ cIscsiInstIndex, cIscsiPortalIndex }
::={ cIscsiTgtPortalAttributesTable 1}
CIscsiTgtPortalAttributesEntry ::=SEQUENCE{
cIscsiTgtPortalPort Unsigned32,
cIscsiTgtPortalTag Unsigned32}cIscsiTgtPortalPort OBJECT-TYPESYNTAXUnsigned32(1..65535)MAX-ACCESSread-write
STATUScurrentDESCRIPTION"The portal's transport protocol port number on which the portal
listens for incoming iSCSI connections when the portal is used
as a target portal."::={ cIscsiTgtPortalAttributesEntry 1}cIscsiTgtPortalTag OBJECT-TYPESYNTAXUnsigned32(1..65535)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The portal's aggregation tag when portal is used as a target
portal. Multiple-connection sessions may be aggregated over
portals sharing an identical aggregation tag."::={ cIscsiTgtPortalAttributesEntry 2}cIscsiInitiatorPortal OBJECTIDENTIFIER::={ cIscsiObjects 5}-- Initiator Portal Attributes TablecIscsiIntrPortalAttributesTable OBJECT-TYPESYNTAXSEQUENCEOF CIscsiIntrPortalAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of Internet Network Addresses (using TCP or another
transport protocol) from which this iSCSI instance may
initiate connections to other targets."
::={ cIscsiInitiatorPortal 1}cIscsiIntrPortalAttributesEntry OBJECT-TYPESYNTAX CIscsiIntrPortalAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry (row) containing management information applicable to
a particular portal instance that is used to initiate
connections to iSCSI targets. This row is populated for each
cIscsiPortalAttributesEntry row that may be used as an
initiator portal."INDEX{ cIscsiInstIndex, cIscsiPortalIndex }
::={ cIscsiIntrPortalAttributesTable 1}
CIscsiIntrPortalAttributesEntry ::=SEQUENCE{
cIscsiIntrPortalTag Unsigned32}cIscsiIntrPortalTag OBJECT-TYPESYNTAXUnsigned32(1..65535)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The portal's aggregation tag when the portal is used as an
initiator portal. Multiple-connection sessions may be
aggregated over portals sharing an identical aggregation tag."::={ cIscsiIntrPortalAttributesEntry 1}cIscsiNode OBJECTIDENTIFIER::={ cIscsiObjects 6}
-- Node Attributes TablecIscsiNodeAttributesTable OBJECT-TYPESYNTAXSEQUENCEOF CIscsiNodeAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of iSCSI nodes belonging to each iSCSI instance present
on the local system. An iSCSI node can act as an initiator, a
target, or both."::={ cIscsiNode 1}cIscsiNodeAttributesEntry OBJECT-TYPESYNTAX CIscsiNodeAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry (row) containing management information applicable to
a particular iSCSI node."INDEX{ cIscsiInstIndex, cIscsiNodeIndex }
::={ cIscsiNodeAttributesTable 1}
CIscsiNodeAttributesEntry ::=SEQUENCE{
cIscsiNodeIndex Unsigned32,
cIscsiNodeName SnmpAdminString,
cIscsiNodeAlias SnmpAdminString,
cIscsiNodeRoles BITS,
cIscsiNodeTransportType RowPointer,
cIscsiNodeInitialR2T TruthValue,
cIscsiNodeBidiInitialR2T TruthValue,
cIscsiNodeImmediateData TruthValue,
cIscsiNodeMaxOutstandingR2T Unsigned32,
cIscsiNodeFirstBurstSize Unsigned32,
cIscsiNodeMaxBurstSize Unsigned32,
cIscsiNodeMaxConnections Unsigned32,
cIscsiNodeDataSequenceInOrder TruthValue,
cIscsiNodeDataPduInOrder TruthValue,
cIscsiNodeDefaultTime2Wait Unsigned32,
cIscsiNodeDefaultTime2Retain Unsigned32,
cIscsiNodeErrorRecoveryLevel Unsigned32}cIscsiNodeIndex OBJECT-TYPESYNTAXUnsigned32(1..4294967295)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An arbitrary integer used to uniquely identify a particular
node within an iSCSI instance present on the local system."::={ cIscsiNodeAttributesEntry 1}cIscsiNodeName OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"A character string that is a globally unique identifier for
this iSCSI node. The node name is independent of the location
of the node, and can be resolved into a set of addresses
through various discovery services."::={ cIscsiNodeAttributesEntry 2}cIscsiNodeAlias OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"A character string that is a human-readable name or description
of the iSCSI node. If configured, this alias may be
communicated to the initiator or target node at the remote end
of the connection during a Login Request or Response message.
This string is not used as an identifier, but can be displayed
by the system's user interface in a list of initiators and/or
targets to which it is connected.
If no alias is configured, this object is a zero-length string."::={ cIscsiNodeAttributesEntry 3}cIscsiNodeRoles OBJECT-TYPESYNTAXBITS{targetTypeNode(0),initiatorTypeNode(1)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"A node can operate as in one or both of two roles:
a target role and/or an initiator role."::={ cIscsiNodeAttributesEntry 4}cIscsiNodeTransportType OBJECT-TYPESYNTAXRowPointerMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"A pointer to the corresponding scsiTrnspt object in the
CISCO-SCSI-MIB (which in turn points to this iSCSI node)
allowing management stations to locate the SCSI-level Device
that is represented by this cIscsiNode."REFERENCE"CISCO-SCSI-MIB"::={ cIscsiNodeAttributesEntry 5}cIscsiNodeInitialR2T OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates InitialR2T preference for this node -
True = YES,
False = will try to negotiate NO, will accept YES "DEFVAL{ true }
::={ cIscsiNodeAttributesEntry 6}cIscsiNodeBidiInitialR2T OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates BidiInitialR2T preference for this node-
True = YES,
False = will try to negotiate NO, will accept YES "DEFVAL{ true }
::={ cIscsiNodeAttributesEntry 7}cIscsiNodeImmediateData OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object indicates ImmediateData preference for this node
True = YES (but will accept NO),
False = NO "DEFVAL{ true }
::={ cIscsiNodeAttributesEntry 8}cIscsiNodeMaxOutstandingR2T OBJECT-TYPESYNTAXUnsigned32(1..65535)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Maximum number of outstanding R2Ts allowed per task."DEFVAL{1}
::={ cIscsiNodeAttributesEntry 9}cIscsiNodeFirstBurstSize OBJECT-TYPESYNTAXUnsigned32(512..16777215)UNITS"bytes"
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The maximum length (bytes) supported for unsolicited data
to/from this node."DEFVAL{65536}
::={ cIscsiNodeAttributesEntry 10}cIscsiNodeMaxBurstSize OBJECT-TYPESYNTAXUnsigned32(512..16777215)UNITS"bytes"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The maximum number of bytes which can be sent within a single
sequence of Data-In or Data-Out PDUs."DEFVAL{262144}
::={ cIscsiNodeAttributesEntry 11}cIscsiNodeMaxConnections OBJECT-TYPESYNTAXUnsigned32(1..65535)UNITS"connections"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The maximum number of connections allowed in each
session to and/or from this node."DEFVAL{1}
::={ cIscsiNodeAttributesEntry 12}cIscsiNodeDataSequenceInOrder OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The DataSequenceInOrder preference of this node.
False (=No) indicates that iSCSI data PDU sequences may
be transferred in any order. True (=Yes) indicates that
data PDU sequences must be transferred using
continuously increasing offsets, except during
error recovery."DEFVAL{ true }
::={ cIscsiNodeAttributesEntry 13}cIscsiNodeDataPduInOrder OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The DataPDUInOrder preference of this node.
False (=No) indicates that iSCSI data PDUs within sequences
may be in any order. True (=Yes) indicates that data PDUs
within sequences must be at continuously increasing
addresses, with no gaps or overlay between PDUs."DEFVAL{ true }
::={ cIscsiNodeAttributesEntry 14}cIscsiNodeDefaultTime2Wait OBJECT-TYPESYNTAXUnsigned32(0..3600)
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The DefaultTime2Wait preference of this node.
This is the minimum time, in seconds, to wait before attempting
an explicit/implicit logout or active task reassignment after
an unexpected connection termination or a connection reset."DEFVAL{2}
::={ cIscsiNodeAttributesEntry 15}cIscsiNodeDefaultTime2Retain OBJECT-TYPESYNTAXUnsigned32(0..3600)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The DefaultTime2Retain preference of this node.
This is the maximum time, in seconds after an initial wait
(Time2Wait), before which an active task reassignment is still
possible after an unexpected connection termination or a
connection reset."DEFVAL{20}
::={ cIscsiNodeAttributesEntry 16}cIscsiNodeErrorRecoveryLevel OBJECT-TYPESYNTAXUnsigned32(0..255)MAX-ACCESSread-writeSTATUScurrent
DESCRIPTION"The ErrorRecoveryLevel preference of this node.
Currently, only 0-2 are valid.
This object is designed to accommodate future error recover
levels.
Higher error recovery levels imply support in addition to
support for the lower error level functions. In otherwords,
error level 2 implies support for levels 0-1, since those
functions are subsets of error level 2."DEFVAL{0}
::={ cIscsiNodeAttributesEntry 17}cIscsiTarget OBJECTIDENTIFIER::={ cIscsiObjects 7}-- Target Attributes TablecIscsiTargetAttributesTable OBJECT-TYPESYNTAXSEQUENCEOF CIscsiTargetAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry (row) containing management information applicable to
a particular node that can take on a target role."::={ cIscsiTarget 1}cIscsiTargetAttributesEntry OBJECT-TYPESYNTAX CIscsiTargetAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry (row) containing management information applicable
to a particular target."INDEX{ cIscsiInstIndex, cIscsiNodeIndex }
::={ cIscsiTargetAttributesTable 1}
CIscsiTargetAttributesEntry ::=SEQUENCE{
cIscsiTgtLoginFailures Counter32,
cIscsiTgtLastFailureTime TimeStamp,
cIscsiTgtLastFailureType AutonomousType,
cIscsiTgtLastIntrFailureName SnmpAdminString,
cIscsiTgtLastIntrFailureAddrType InetAddressType,
cIscsiTgtLastIntrFailureAddr InetAddress}cIscsiTgtLoginFailures OBJECT-TYPESYNTAXCounter32UNITS"failed login attempts"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object counts the number of times a login attempt to this
local target has failed."::={ cIscsiTargetAttributesEntry 1}cIscsiTgtLastFailureTime OBJECT-TYPESYNTAXTimeStampMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The timestamp of the most recent failure of a login attempt to
this target. A value of zero indicates that no such failures
have occurred."::={ cIscsiTargetAttributesEntry 2}
cIscsiTgtLastFailureType OBJECT-TYPESYNTAXAutonomousTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The type of the most recent failure of a login attempt to this
target, represented as the OID of the counter object in
cIscsiTargetLoginStatsTable for which the relevant instance was
incremented. A value of 0.0 indicates a type which is not
represented by any of the counters in
cIscsiTargetLoginStatsTable."::={ cIscsiTargetAttributesEntry 3}cIscsiTgtLastIntrFailureName OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"An octet string giving the name of the initiator
that failed the last login attempt."::={ cIscsiTargetAttributesEntry 4}cIscsiTgtLastIntrFailureAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The type of Internet Network Address in
cIscsiTgtLastIntrFailureAddr."::={ cIscsiTargetAttributesEntry 5}cIscsiTgtLastIntrFailureAddr OBJECT-TYPE
SYNTAXInetAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"An Internet Network Address giving the host address
of the initiator that failed the last login attempt."::={ cIscsiTargetAttributesEntry 6}-- Target Login Stats TablecIscsiTargetLoginStatsTable OBJECT-TYPESYNTAXSEQUENCEOF CIscsiTargetLoginStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of counters which keep a record of the results
of initiators' login attempts to this target."::={ cIscsiTarget 2}cIscsiTargetLoginStatsEntry OBJECT-TYPESYNTAX CIscsiTargetLoginStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry (row) containing counters for each result of
a login attempt to this target."AUGMENTS{ cIscsiTargetAttributesEntry }
::={ cIscsiTargetLoginStatsTable 1}
CIscsiTargetLoginStatsEntry ::=SEQUENCE{
cIscsiTgtLoginAccepts Counter32,
cIscsiTgtLoginOtherFails Counter32,
cIscsiTgtLoginRedirects Counter32,
cIscsiTgtLoginAuthorizeFails Counter32,
cIscsiTgtLoginAuthenticateFails Counter32,
cIscsiTgtLoginNegotiateFails Counter32}cIscsiTgtLoginAccepts OBJECT-TYPESYNTAXCounter32UNITS"successful logins"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of Login Response PDUs with status
0x0000, Accept Login, transmitted by this
target."::={ cIscsiTargetLoginStatsEntry 1}cIscsiTgtLoginOtherFails OBJECT-TYPESYNTAXCounter32UNITS"failed logins"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of Login Response PDUs which were transmitted
by this target, and which were not counted by any other
object in the row."::={ cIscsiTargetLoginStatsEntry 2}cIscsiTgtLoginRedirects OBJECT-TYPESYNTAXCounter32UNITS"failed logins"
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of Login Response PDUs with status class 0x01,
Redirection, transmitted by this target."::={ cIscsiTargetLoginStatsEntry 3}cIscsiTgtLoginAuthorizeFails OBJECT-TYPESYNTAXCounter32UNITS"failed logins"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of Login Response PDUs with status 0x0202,
Forbidden Target, transmitted by this target.
If this counter is incremented, an cIscsiTgtLoginFailure
notification should be generated."::={ cIscsiTargetLoginStatsEntry 4}cIscsiTgtLoginAuthenticateFails OBJECT-TYPESYNTAXCounter32UNITS"failed logins"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of Login Response PDUs with status 0x0201,
Authentication Failed, transmitted by this target
If this counter is incremented, an cIscsiTgtLoginFailure
notification should be generated."::={ cIscsiTargetLoginStatsEntry 5}cIscsiTgtLoginNegotiateFails OBJECT-TYPE
SYNTAXCounter32UNITS"failed logins"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of times a target has effectively refused a
login because the parameter negotiation failed.
[Ed. While this situation can occur, the exact mechanism
is as yet undefined in the iSCSI Protocol Spec.]
If this counter is incremented, an cIscsiTgtLoginFailure
notification should be generated."::={ cIscsiTargetLoginStatsEntry 6}-- Target Logout Stats TablecIscsiTargetLogoutStatsTable OBJECT-TYPESYNTAXSEQUENCEOF CIscsiTargetLogoutStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"When a target receives a Logout command, it responds
with a Logout Response that carries a status code.
This table contains counters for both normal and
abnormal logout requests received by this target."::={ cIscsiTarget 3}cIscsiTargetLogoutStatsEntry OBJECT-TYPESYNTAX CIscsiTargetLogoutStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry (row) containing counters of Logout Response
PDUs that were received by this target."AUGMENTS{ cIscsiTargetAttributesEntry }
::={ cIscsiTargetLogoutStatsTable 1}
CIscsiTargetLogoutStatsEntry ::=SEQUENCE{
cIscsiTgtLogoutNormals Counter32,
cIscsiTgtLogoutOthers Counter32}cIscsiTgtLogoutNormals OBJECT-TYPESYNTAXCounter32UNITS"normal logouts"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of Logout Command PDUs received by this target,
with reason code 0 (closes the session)."::={ cIscsiTargetLogoutStatsEntry 1}cIscsiTgtLogoutOthers OBJECT-TYPESYNTAXCounter32UNITS"abnormal logouts"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of Logout Command PDUs received by this target,
with any status code other than 0."::={ cIscsiTargetLogoutStatsEntry 2}cIscsiTgtAuthorization OBJECTIDENTIFIER::={ cIscsiObjects 8}-- Target Authorization Attributes Table
cIscsiTgtAuthAttributesTable OBJECT-TYPESYNTAXSEQUENCEOF CIscsiTgtAuthAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of initiator identities that are authorized to
access each target node within each iSCSI instance
present on the local system."::={ cIscsiTgtAuthorization 1}cIscsiTgtAuthAttributesEntry OBJECT-TYPESYNTAX CIscsiTgtAuthAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry (row) containing management information
applicable to a particular target node's authorized
initiator identity."INDEX{ cIscsiInstIndex, cIscsiNodeIndex, cIscsiTgtAuthIndex }
::={ cIscsiTgtAuthAttributesTable 1}
CIscsiTgtAuthAttributesEntry ::=SEQUENCE{
cIscsiTgtAuthIndex Unsigned32,
cIscsiTgtAuthRowStatus RowStatus,
cIscsiTgtAuthIdentity RowPointer}cIscsiTgtAuthIndex OBJECT-TYPESYNTAXUnsigned32(1..4294967295)
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An arbitrary integer used to uniquely identify a particular
target's authorized initiator identity within an iSCSI
instance present on the local system."::={ cIscsiTgtAuthAttributesEntry 1}cIscsiTgtAuthRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The status of the row."::={ cIscsiTgtAuthAttributesEntry 2}cIscsiTgtAuthIdentity OBJECT-TYPESYNTAXRowPointerMAX-ACCESSread-createSTATUScurrentDESCRIPTION"A pointer to the corresponding IPS-AUTH MIB user entry
that will be allowed to access this iSCSI target."REFERENCE"IPS-AUTH MIB"::={ cIscsiTgtAuthAttributesEntry 3}cIscsiInitiator OBJECTIDENTIFIER::={ cIscsiObjects 9}-- Initiator Attributes TablecIscsiInitiatorAttributesTable OBJECT-TYPE
SYNTAXSEQUENCEOF CIscsiInitiatorAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of iSCSI nodes that can take on an initiator
role, belonging to each iSCSI instance present on
the local system."::={ cIscsiInitiator 1}cIscsiInitiatorAttributesEntry OBJECT-TYPESYNTAX CIscsiInitiatorAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry (row) containing management information
applicable to a particular iSCSI node that has
initiator capabilities."INDEX{ cIscsiInstIndex, cIscsiNodeIndex }
::={ cIscsiInitiatorAttributesTable 1}
CIscsiInitiatorAttributesEntry ::=SEQUENCE{
cIscsiIntrLoginFailures Counter32,
cIscsiIntrLastFailureTime TimeStamp,
cIscsiIntrLastFailureType AutonomousType,
cIscsiIntrLastTgtFailureName SnmpAdminString,
cIscsiIntrLastTgtFailureAddrType InetAddressType,
cIscsiIntrLastTgtFailureAddr InetAddress}cIscsiIntrLoginFailures OBJECT-TYPESYNTAXCounter32
UNITS"failed logins"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object counts the number of times a login attempt from
this local initiator has failed."::={ cIscsiInitiatorAttributesEntry 1}cIscsiIntrLastFailureTime OBJECT-TYPESYNTAXTimeStampMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The timestamp of the most recent failure of a login attempt
from this initiator. A value of zero indicates that no such
failures have occurred."::={ cIscsiInitiatorAttributesEntry 2}cIscsiIntrLastFailureType OBJECT-TYPESYNTAXAutonomousTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The type of the most recent failure of a login attempt
from this initiator, represented as the OID of the counter
object in cIscsiInitiatorLoginStatsTable for which the
relevant instance was incremented. A value of 0.0
indicates a type which is not represented by any of
the counters in cIscsiInitiatorLoginStatsTable."::={ cIscsiInitiatorAttributesEntry 3}cIscsiIntrLastTgtFailureName OBJECT-TYPE
SYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"An octet string giving the name of the target that failed
the last login attempt."::={ cIscsiInitiatorAttributesEntry 4}cIscsiIntrLastTgtFailureAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The type of Internet Network Address in
cIscsiIntrLastTgtFailureAddr."::={ cIscsiInitiatorAttributesEntry 5}cIscsiIntrLastTgtFailureAddr OBJECT-TYPESYNTAXInetAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"An Internet Network Address giving the host address of the
target that failed the last login attempt."::={ cIscsiInitiatorAttributesEntry 6}-- Initiator Login Stats TablecIscsiInitiatorLoginStatsTable OBJECT-TYPESYNTAXSEQUENCEOF CIscsiInitiatorLoginStatsEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"A table of counters which keep track of the results of
this initiator's login attempts."::={ cIscsiInitiator 2}cIscsiInitiatorLoginStatsEntry OBJECT-TYPESYNTAX CIscsiInitiatorLoginStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry (row) containing counters of each result
of this initiator's login attempts."AUGMENTS{ cIscsiInitiatorAttributesEntry }
::={ cIscsiInitiatorLoginStatsTable 1}
CIscsiInitiatorLoginStatsEntry ::=SEQUENCE{
cIscsiIntrLoginAcceptRsps Counter32,
cIscsiIntrLoginOtherFailRsps Counter32,
cIscsiIntrLoginRedirectRsps Counter32,
cIscsiIntrLoginAuthFailRsps Counter32,
cIscsiIntrLoginAuthenticateFails Counter32,
cIscsiIntrLoginNegotiateFails Counter32}cIscsiIntrLoginAcceptRsps OBJECT-TYPESYNTAXCounter32UNITS"successful logins"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"The count of Login Response PDUs with status
0x0000, Accept Login, received by this initiator."::={ cIscsiInitiatorLoginStatsEntry 1}cIscsiIntrLoginOtherFailRsps OBJECT-TYPESYNTAXCounter32UNITS"failed logins"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of Login Response PDUs received by this
initiator with any status code not counted in the
objects below."::={ cIscsiInitiatorLoginStatsEntry 2}cIscsiIntrLoginRedirectRsps OBJECT-TYPESYNTAXCounter32UNITS"failed logins"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of Login Response PDUs with status class 0x01,
Redirection, received by this initiator."::={ cIscsiInitiatorLoginStatsEntry 3}cIscsiIntrLoginAuthFailRsps OBJECT-TYPESYNTAXCounter32UNITS"failed logins"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of Login Response PDUs with status class 0x201,
Authentication Failed, received by this initiator."::={ cIscsiInitiatorLoginStatsEntry 4}cIscsiIntrLoginAuthenticateFails OBJECT-TYPESYNTAXCounter32UNITS"failed logins"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of times the initiator has aborted a
login because the target could not be authenticated.
No response is generated.
If this counter is incremented, an cIscsiIntrLoginFailure
notification should be generated."::={ cIscsiInitiatorLoginStatsEntry 5}cIscsiIntrLoginNegotiateFails OBJECT-TYPESYNTAXCounter32UNITS"failed logins"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of times the initiator has aborted a
login because parameter negotiation with the target
failed.
No response is generated.
If this counter is incremented, an cIscsiIntrLoginFailure
notification should be generated."::={ cIscsiInitiatorLoginStatsEntry 6}-- Initiator Logout Stats TablecIscsiInitiatorLogoutStatsTable OBJECT-TYPESYNTAXSEQUENCEOF CIscsiInitiatorLogoutStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"When an initiator attempts send a Logout command, the target
responds with a Logout Response that carries a status code.
This table contains a list of counters of Logout Response
PDUs of each status code, that were received by each
initiator belonging to this iSCSI instance present on this
system."::={ cIscsiInitiator 3}cIscsiInitiatorLogoutStatsEntry OBJECT-TYPESYNTAX CIscsiInitiatorLogoutStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry (row) containing counters of Logout Response
PDUs of each status code, that were generated by this
initiator."AUGMENTS{ cIscsiInitiatorAttributesEntry }
::={ cIscsiInitiatorLogoutStatsTable 1}
CIscsiInitiatorLogoutStatsEntry ::=SEQUENCE{
cIscsiIntrLogoutNormals Counter32,
cIscsiIntrLogoutOthers Counter32}cIscsiIntrLogoutNormals OBJECT-TYPESYNTAXCounter32UNITS"normal logouts"MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"The count of Logout Command PDUs generated by this initiator
with reason code 0 (closes the session)."::={ cIscsiInitiatorLogoutStatsEntry 1}cIscsiIntrLogoutOthers OBJECT-TYPESYNTAXCounter32UNITS"abnormal logouts"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of Logout Command PDUs generated by this initiator
with any status code other than 0."::={ cIscsiInitiatorLogoutStatsEntry 2}cIscsiIntrAuthorization OBJECTIDENTIFIER::={ cIscsiObjects 10}-- Initiator Authorization Attributes TablecIscsiIntrAuthAttributesTable OBJECT-TYPESYNTAXSEQUENCEOF CIscsiIntrAuthAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of target identities which each initiator
on the local system may access."::={ cIscsiIntrAuthorization 1}cIscsiIntrAuthAttributesEntry OBJECT-TYPESYNTAX CIscsiIntrAuthAttributesEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"An entry (row) containing management information applicable
to a particular initiator node's authorized target identity."INDEX{ cIscsiInstIndex, cIscsiNodeIndex, cIscsiIntrAuthIndex }
::={ cIscsiIntrAuthAttributesTable 1}
CIscsiIntrAuthAttributesEntry ::=SEQUENCE{
cIscsiIntrAuthIndex Unsigned32,
cIscsiIntrAuthRowStatus RowStatus,
cIscsiIntrAuthIdentity RowPointer}cIscsiIntrAuthIndex OBJECT-TYPESYNTAXUnsigned32(1..4294967295)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An arbitrary integer used to uniquely identify a
particular initiator node's authorized target
identity within an iSCSI instance present on the
local system."::={ cIscsiIntrAuthAttributesEntry 1}cIscsiIntrAuthRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"The status of the row."::={ cIscsiIntrAuthAttributesEntry 2}cIscsiIntrAuthIdentity OBJECT-TYPESYNTAXRowPointerMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"A pointer to the corresponding IPS-AUTH MIB user entry
to which this initiator node should attempt to establish
an iSCSI session."REFERENCE"IPS-AUTH MIB"::={ cIscsiIntrAuthAttributesEntry 3}cIscsiSession OBJECTIDENTIFIER::={ cIscsiObjects 11}-- Session Attributes TablecIscsiSessionAttributesTable OBJECT-TYPESYNTAXSEQUENCEOF CIscsiSessionAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of sessions belonging to each iSCSI instance
present on the system."::={ cIscsiSession 1}cIscsiSessionAttributesEntry OBJECT-TYPESYNTAX CIscsiSessionAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION
"An entry (row) containing management information applicable
to a particular session."INDEX{ cIscsiInstIndex, cIscsiNodeIndex, cIscsiSsnIndex }
::={ cIscsiSessionAttributesTable 1}
CIscsiSessionAttributesEntry ::=SEQUENCE{
cIscsiSsnIndex Unsigned32,
cIscsiSsnDirection INTEGER,
cIscsiSsnInitiatorName SnmpAdminString,
cIscsiSsnTargetName SnmpAdminString,
cIscsiSsnTsih Unsigned32,
cIscsiSsnIsid OCTETSTRING,
cIscsiSsnInitiatorAlias SnmpAdminString,
cIscsiSsnTargetAlias SnmpAdminString,
cIscsiSsnInitialR2T TruthValue,
cIscsiSsnBidiInitialR2T TruthValue,
cIscsiSsnImmediateData TruthValue,
cIscsiSsnType INTEGER,
cIscsiSsnMaxOutstandingR2T Unsigned32,
cIscsiSsnFirstBurstSize Unsigned32,
cIscsiSsnMaxBurstSize Unsigned32,
cIscsiSsnConnectionNumber Gauge32,
cIscsiSsnAuthIdentity RowPointer,
cIscsiSsnDataSequenceInOrder TruthValue,
cIscsiSsnDataPduInOrder TruthValue,
cIscsiSsnErrorRecoveryLevel Unsigned32}cIscsiSsnIndex OBJECT-TYPESYNTAXUnsigned32(1..4294967295)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An arbitrary integer used to uniquely identify a
particular session within an iSCSI instance present
on the local system."::={ cIscsiSessionAttributesEntry 1}cIscsiSsnDirection OBJECT-TYPESYNTAXINTEGER{inboundSession(1),outboundSession(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Direction of iSCSI session:
InboundSession - session is established from an external
initiator to a target within this iSCSI
instance.
OutboundSession - session is established from an initiator
within this iSCSI instance to an external
target."
::={ cIscsiSessionAttributesEntry 2}cIscsiSsnInitiatorName OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If cIscsiSsnDirection is Inbound, this object is an
octet string that will contain the name of the remote
initiator.
If cIscsiSsnDirection is Outbound, this object will
contain a zero-length string."::={ cIscsiSessionAttributesEntry 3}cIscsiSsnTargetName OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If cIscsiSsnDirection is Outbound, this object is an
octet string that will contain the name of the remote
target.
If cIscsiSsnDirection is Inbound, this object will
contain a zero-length string."::={ cIscsiSessionAttributesEntry 4}cIscsiSsnTsih OBJECT-TYPESYNTAXUnsigned32(1..65535)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The target-defined identification handle for this session."
::={ cIscsiSessionAttributesEntry 5}cIscsiSsnIsid OBJECT-TYPESYNTAXOCTETSTRING(SIZE(6))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The initiator-defined portion of the iSCSI Session ID."::={ cIscsiSessionAttributesEntry 6}cIscsiSsnInitiatorAlias OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"An octet string that gives the alias communicated by the
initiator end of the session during the login phase.
If no alias exists, the value is a zero-length string."::={ cIscsiSessionAttributesEntry 7}cIscsiSsnTargetAlias OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"An octet string that gives the alias communicated by the
target end of the session during the login phase.
If no alias exists, the value is a zero-length string."::={ cIscsiSessionAttributesEntry 8}
cIscsiSsnInitialR2T OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If set to true, indicates that the initiator must wait
for an R2T before sending to the target. If set to false,
the initiator may send data immediately, within limits set
by cIscsiSsnFirstBurstSize and the expected data transfer
length of the request.
Default is true."::={ cIscsiSessionAttributesEntry 9}cIscsiSsnBidiInitialR2T OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If set to true, indicates that the initiator must wait
for an R2T before sending data to the target within a
bi-directional (both read and write) request. If false,
the initiator may send unsolicited write data as part
of the request."::={ cIscsiSessionAttributesEntry 10}cIscsiSsnImmediateData OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates whether the initiator and target have agreed to
support immediate data on this session."::={ cIscsiSessionAttributesEntry 11}
cIscsiSsnType OBJECT-TYPESYNTAXINTEGER{normalSession(1),discoverySession(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Type of iSCSI session:
normalSession - session is a normal iSCSI session
discoverySession - session is being used only for discovery."DEFVAL{ normalSession }
::={ cIscsiSessionAttributesEntry 12}cIscsiSsnMaxOutstandingR2T OBJECT-TYPESYNTAXUnsigned32(1..65535)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The maximum number of outstanding request-to-transmit
(R2T)s per task within this session."::={ cIscsiSessionAttributesEntry 13}cIscsiSsnFirstBurstSize OBJECT-TYPESYNTAXUnsigned32(512..16777215)
UNITS"bytes"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The maximum length supported for unsolicited data sent
within this session."DEFVAL{65536}
::={ cIscsiSessionAttributesEntry 14}cIscsiSsnMaxBurstSize OBJECT-TYPESYNTAXUnsigned32(512..16777215)UNITS"bytes"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The maximum number of bytes which can be sent within
a single sequence of Data-In or Data-Out PDUs."DEFVAL{262144}
::={ cIscsiSessionAttributesEntry 15}cIscsiSsnConnectionNumber OBJECT-TYPESYNTAXGauge32(1..65535)UNITS"connections"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of transport protocol connections that currently
belong to this session."::={ cIscsiSessionAttributesEntry 16}cIscsiSsnAuthIdentity OBJECT-TYPESYNTAXRowPointerMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains a row in the IPS-AUTH MIB
which identifies the authentication method
being used on this session, as communicated
during the login phase."REFERENCE"IPS-AUTH MIB"::={ cIscsiSessionAttributesEntry 17}cIscsiSsnDataSequenceInOrder OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"False indicates that iSCSI data PDU sequences may
be transferred in any order. True indicates that
data PDU sequences must be transferred using
continuously increasing offsets, except during
error recovery."::={ cIscsiSessionAttributesEntry 18}cIscsiSsnDataPduInOrder OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"False indicates that iSCSI data PDUs within sequences
may be in any order. True indicates that data PDUs
within sequences must be at continuously increasing
addresses, with no gaps or overlay between PDUs.
Default is true."::={ cIscsiSessionAttributesEntry 19}cIscsiSsnErrorRecoveryLevel OBJECT-TYPESYNTAXUnsigned32(0..255)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The level of error recovery negotiated between
the initiator and the target. Higher numbers
represent more detailed recovery schemes."::={ cIscsiSessionAttributesEntry 20}-- Session Stats TablecIscsiSessionStatsTable OBJECT-TYPESYNTAXSEQUENCEOF CIscsiSessionStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of general iSCSI traffic counters for each of the
sessions present on the system."::={ cIscsiSession 2}cIscsiSessionStatsEntry OBJECT-TYPESYNTAX CIscsiSessionStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry (row) containing general iSCSI traffic counters
for a particular session."AUGMENTS{ cIscsiSessionAttributesEntry }
::={ cIscsiSessionStatsTable 1}
CIscsiSessionStatsEntry ::=SEQUENCE{
cIscsiSsnCmdPdus Counter32,
cIscsiSsnRspPdus Counter32,
cIscsiSsnTxDataOctets Counter64,
cIscsiSsnRxDataOctets Counter64}cIscsiSsnCmdPdus OBJECT-TYPESYNTAXCounter32UNITS"PDUs"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of Command PDUs transferred on this session."::={ cIscsiSessionStatsEntry 1}cIscsiSsnRspPdus OBJECT-TYPESYNTAXCounter32UNITS"PDUs"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of Response PDUs transferred on this session."::={ cIscsiSessionStatsEntry 2}cIscsiSsnTxDataOctets OBJECT-TYPESYNTAXCounter64
UNITS"octets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of data octets that were transmitted by
the local iSCSI node on this session."::={ cIscsiSessionStatsEntry 3}cIscsiSsnRxDataOctets OBJECT-TYPESYNTAXCounter64UNITS"octets"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of data octets that were received by
the local iSCSI node on this session."::={ cIscsiSessionStatsEntry 4}-- Session Connection Error Stats TablecIscsiSessionCxnErrorStatsTable OBJECT-TYPESYNTAXSEQUENCEOF CIscsiSessionCxnErrorStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of error counters for each of the sessions
present on this system."::={ cIscsiSession 3}cIscsiSessionCxnErrorStatsEntry OBJECT-TYPESYNTAX CIscsiSessionCxnErrorStatsEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"An entry (row) containing error counters for
a particular session."AUGMENTS{ cIscsiSessionAttributesEntry }
::={ cIscsiSessionCxnErrorStatsTable 1}
CIscsiSessionCxnErrorStatsEntry ::=SEQUENCE{
cIscsiSsnDigestErrors Counter32,
cIscsiSsnCxnTimeoutErrors Counter32}cIscsiSsnDigestErrors OBJECT-TYPESYNTAXCounter32UNITS"PDUs"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of PDUs which were received on the session and
contained header or data digest errors."::={ cIscsiSessionCxnErrorStatsEntry 1}cIscsiSsnCxnTimeoutErrors OBJECT-TYPESYNTAXCounter32UNITS"sequences"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The count of connections within this session
which have been terminated due to timeout."::={ cIscsiSessionCxnErrorStatsEntry 2}cIscsiConnection OBJECTIDENTIFIER::={ cIscsiObjects 12}
-- Connection Attributes TablecIscsiConnectionAttributesTable OBJECT-TYPESYNTAXSEQUENCEOF CIscsiConnectionAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of connections belonging to each iSCSI instance
present on the system."::={ cIscsiConnection 1}cIscsiConnectionAttributesEntry OBJECT-TYPESYNTAX CIscsiConnectionAttributesEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry (row) containing management information applicable
to a particular connection."INDEX{ cIscsiInstIndex, cIscsiNodeIndex, cIscsiSsnIndex,
cIscsiCxnIndex }
::={ cIscsiConnectionAttributesTable 1}
CIscsiConnectionAttributesEntry ::=SEQUENCE{
cIscsiCxnIndex Unsigned32,
cIscsiCxnCid Unsigned32,
cIscsiCxnState INTEGER,
cIscsiCxnLocalAddrType InetAddressType,
cIscsiCxnLocalAddr InetAddress,
cIscsiCxnProtocol CIscsiTransportProtocols,
cIscsiCxnLocalPort Unsigned32,
cIscsiCxnRemoteAddrType InetAddressType,
cIscsiCxnRemoteAddr InetAddress,
cIscsiCxnRemotePort Unsigned32,
cIscsiCxnMaxRecvDataSegLength Unsigned32,
cIscsiCxnHeaderIntegrity CIscsiDigestMethod,
cIscsiCxnDataIntegrity CIscsiDigestMethod,
cIscsiCxnRecvMarker TruthValue,
cIscsiCxnSendMarker TruthValue}cIscsiCxnIndex OBJECT-TYPESYNTAXUnsigned32(1..4294967295)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An arbitrary integer used to uniquely identify a
particular connection of a particular session within
an iSCSI instance present on the local system."::={ cIscsiConnectionAttributesEntry 1}cIscsiCxnCid OBJECT-TYPESYNTAXUnsigned32(1..65535)MAX-ACCESSread-only
STATUScurrentDESCRIPTION"The iSCSI Connection ID for this connection."::={ cIscsiConnectionAttributesEntry 2}cIscsiCxnState OBJECT-TYPESYNTAXINTEGER{login(1),full(2),logout(3)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The current state of this connection, from an iSCSI negotiation
point of view. Here are the states:
login - The transport protocol connection has been established,
but a valid iSCSI login response with the final bit set
has not been sent or received.
full - A valid iSCSI login response with the final bit set
has been sent or received.
logout - A valid iSCSI logout command has been sent or
received, but the transport protocol connection has
not yet been closed."::={ cIscsiConnectionAttributesEntry 3}cIscsiCxnLocalAddrType OBJECT-TYPESYNTAXInetAddressTypeMAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"The type of Internet Network Address in cIscsiCxnLocalAddr."::={ cIscsiConnectionAttributesEntry 4}cIscsiCxnLocalAddr OBJECT-TYPESYNTAXInetAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The local Internet Network Address used by this connection."::={ cIscsiConnectionAttributesEntry 5}cIscsiCxnProtocol OBJECT-TYPESYNTAX CIscsiTransportProtocols
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The transport protocol over which this connection is
running."DEFVAL{6}-- TCP::={ cIscsiConnectionAttributesEntry 6}cIscsiCxnLocalPort OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The local transport protocol port used by this connection."::={ cIscsiConnectionAttributesEntry 7}cIscsiCxnRemoteAddrType OBJECT-TYPE
SYNTAXInetAddressTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The type of Internet Network Address in cIscsiCxnRemoteAddr."::={ cIscsiConnectionAttributesEntry 8}cIscsiCxnRemoteAddr OBJECT-TYPESYNTAXInetAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The remote Internet Network Address used by this connection."::={ cIscsiConnectionAttributesEntry 9}cIscsiCxnRemotePort OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The remote transport protocol port used by this connection."::={ cIscsiConnectionAttributesEntry 10}cIscsiCxnMaxRecvDataSegLength OBJECT-TYPESYNTAXUnsigned32(512..16777215)UNITS"bytes"MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"The maximum data payload size supported for command
or data PDUs in use within this connection.
Note that the size of reported in bytes even though
the negotiation is in 512k blocks."DEFVAL{8192}
::={ cIscsiConnectionAttributesEntry 11}cIscsiCxnHeaderIntegrity OBJECT-TYPESYNTAX CIscsiDigestMethod
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object identifies the iSCSI header
digest scheme in use within this connection."::={ cIscsiConnectionAttributesEntry 12}cIscsiCxnDataIntegrity OBJECT-TYPESYNTAX CIscsiDigestMethod
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object identifies the iSCSI data
digest scheme in use within this connection."::={ cIscsiConnectionAttributesEntry 13}cIscsiCxnRecvMarker OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates whether or not this connection
is receiving markers in in its incoming data stream."
::={ cIscsiConnectionAttributesEntry 14}cIscsiCxnSendMarker OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates whether or not this connection
is inserting markers in in its outgoing data stream."::={ cIscsiConnectionAttributesEntry 15}-- NotificationscIscsiNotificationsPrefix OBJECTIDENTIFIER::={ cIscsiNotifications 0}cIscsiTgtLoginFailure NOTIFICATION-TYPEOBJECTS{
cIscsiTgtLoginFailures,
cIscsiTgtLastFailureType,
cIscsiTgtLastIntrFailureName,
cIscsiTgtLastIntrFailureAddrType,
cIscsiTgtLastIntrFailureAddr
}STATUScurrentDESCRIPTION"Sent when a login is failed by a target.
The implementation of this trap should not send more than
3 notifications of this type in any 10 second time span."::={ cIscsiNotificationsPrefix 1}cIscsiIntrLoginFailure NOTIFICATION-TYPEOBJECTS{
cIscsiIntrLoginFailures,
cIscsiIntrLastFailureType,
cIscsiIntrLastTgtFailureName,
cIscsiIntrLastTgtFailureAddrType,
cIscsiIntrLastTgtFailureAddr
}STATUScurrentDESCRIPTION"Sent when a login is failed by a initiator.
The implementation of this trap should not send more than
3 notifications of this type in any 10 second time span."::={ cIscsiNotificationsPrefix 2}cIscsiInstSessionFailure NOTIFICATION-TYPEOBJECTS{
cIscsiInstSsnFailures,
cIscsiInstLastSsnFailureType,
cIscsiInstLastSsnRmtNodeName
}STATUScurrentDESCRIPTION"Sent when an active session is failed by either the initiator
or the target.
The implementation of this trap should not send more than
3 notifications of this type in any 10 second time span."::={ cIscsiNotificationsPrefix 3}-- Conformance StatementscIscsiGroups OBJECTIDENTIFIER::={ cIscsiConformance 1}cIscsiInstanceAttributesGroup OBJECT-GROUPOBJECTS{
cIscsiInstDescr,
cIscsiInstVersionMin,
cIscsiInstVersionMax,
cIscsiInstVendorID,
cIscsiInstVendorVersion,
cIscsiInstPortalNumber,
cIscsiInstNodeNumber,
cIscsiInstSessionNumber,
cIscsiInstSsnFailures,
cIscsiInstLastSsnFailureType,
cIscsiInstLastSsnRmtNodeName
}STATUScurrentDESCRIPTION"A collection of objects providing information about iSCSI
instances."::={ cIscsiGroups 1}cIscsiInstanceSsnErrorStatsGroup OBJECT-GROUPOBJECTS{
cIscsiInstSsnDigestErrors,
cIscsiInstSsnCxnTimeoutErrors,
cIscsiInstSsnFormatErrors
}STATUScurrentDESCRIPTION"A collection of objects providing information about
errors that have caused a session failure for an
iSCSI instance."::={ cIscsiGroups 2}cIscsiPortalAttributesGroup OBJECT-GROUPOBJECTS{
cIscsiPortalRowStatus,
cIscsiPortalRoles,
cIscsiPortalAddrType,
cIscsiPortalAddr,
cIscsiPortalProtocol,
cIscsiPortalMaxRecvDataSegLength,
cIscsiPortalPrimaryHdrDigest,
cIscsiPortalPrimaryDataDigest,
cIscsiPortalSecondaryHdrDigest,
cIscsiPortalSecondaryDataDigest,
cIscsiPortalRecvMarker
}STATUScurrentDESCRIPTION"A collection of objects providing information about
the transport protocol endpoints of the local targets."::={ cIscsiGroups 3}cIscsiTgtPortalAttributesGroup OBJECT-GROUPOBJECTS{
cIscsiTgtPortalPort,
cIscsiTgtPortalTag
}STATUScurrentDESCRIPTION"A collection of objects providing information about
the transport protocol endpoints of the local targets."::={ cIscsiGroups 4}cIscsiIntrPortalAttributesGroup OBJECT-GROUPOBJECTS{
cIscsiIntrPortalTag
}STATUScurrentDESCRIPTION"A collection of objects providing information about
the Internet Network Addresses of the local initiators."::={ cIscsiGroups 5}cIscsiNodeAttributesGroup OBJECT-GROUPOBJECTS{
cIscsiNodeName,
cIscsiNodeAlias,
cIscsiNodeRoles,
cIscsiNodeTransportType,
cIscsiNodeInitialR2T,
cIscsiNodeBidiInitialR2T,
cIscsiNodeImmediateData,
cIscsiNodeMaxOutstandingR2T,
cIscsiNodeFirstBurstSize,
cIscsiNodeMaxBurstSize,
cIscsiNodeMaxConnections,
cIscsiNodeDataSequenceInOrder,
cIscsiNodeDataPduInOrder,
cIscsiNodeDefaultTime2Wait,
cIscsiNodeDefaultTime2Retain,
cIscsiNodeErrorRecoveryLevel
}STATUScurrentDESCRIPTION"A collection of objects providing information about all
local targets."::={ cIscsiGroups 6}cIscsiTargetAttributesGroup OBJECT-GROUPOBJECTS{
cIscsiTgtLoginFailures,
cIscsiTgtLastFailureTime,
cIscsiTgtLastFailureType,
cIscsiTgtLastIntrFailureName,
cIscsiTgtLastIntrFailureAddrType,
cIscsiTgtLastIntrFailureAddr
}STATUScurrentDESCRIPTION"A collection of objects providing information about all
local targets."::={ cIscsiGroups 7}cIscsiTargetLoginStatsGroup OBJECT-GROUPOBJECTS{
cIscsiTgtLoginAccepts,
cIscsiTgtLoginOtherFails,
cIscsiTgtLoginRedirects,
cIscsiTgtLoginAuthorizeFails,
cIscsiTgtLoginAuthenticateFails,
cIscsiTgtLoginNegotiateFails
}STATUScurrentDESCRIPTION"A collection of objects providing information about all
login attempts by remote initiators to local targets."::={ cIscsiGroups 8}cIscsiTargetLogoutStatsGroup OBJECT-GROUPOBJECTS{
cIscsiTgtLogoutNormals,
cIscsiTgtLogoutOthers
}STATUScurrentDESCRIPTION"A collection of objects providing information about all
logout events between remote initiators to local targets."::={ cIscsiGroups 9}cIscsiTargetAuthGroup OBJECT-GROUPOBJECTS{
cIscsiTgtAuthRowStatus,
cIscsiTgtAuthIdentity
}STATUScurrentDESCRIPTION"."::={ cIscsiGroups 10}cIscsiInitiatorAttributesGroup OBJECT-GROUPOBJECTS{
cIscsiIntrLoginFailures,
cIscsiIntrLastFailureTime,
cIscsiIntrLastFailureType,
cIscsiIntrLastTgtFailureName,
cIscsiIntrLastTgtFailureAddrType,
cIscsiIntrLastTgtFailureAddr
}STATUScurrent
DESCRIPTION"A collection of objects providing information about
all local initiators."::={ cIscsiGroups 11}cIscsiInitiatorLoginStatsGroup OBJECT-GROUPOBJECTS{
cIscsiIntrLoginAcceptRsps,
cIscsiIntrLoginOtherFailRsps,
cIscsiIntrLoginRedirectRsps,
cIscsiIntrLoginAuthFailRsps,
cIscsiIntrLoginAuthenticateFails,
cIscsiIntrLoginNegotiateFails
}STATUScurrentDESCRIPTION"A collection of objects providing information about all
login attempts by local initiators to remote targets."::={ cIscsiGroups 12}cIscsiInitiatorLogoutStatsGroup OBJECT-GROUPOBJECTS{
cIscsiIntrLogoutNormals,
cIscsiIntrLogoutOthers
}STATUScurrentDESCRIPTION"A collection of objects providing information about all
logout events between local initiators to remote targets."::={ cIscsiGroups 13}cIscsiInitiatorAuthGroup OBJECT-GROUPOBJECTS{
cIscsiIntrAuthRowStatus,
cIscsiIntrAuthIdentity
}STATUScurrent
DESCRIPTION"."::={ cIscsiGroups 14}cIscsiSessionAttributesGroup OBJECT-GROUPOBJECTS{
cIscsiSsnDirection,
cIscsiSsnInitiatorName,
cIscsiSsnTargetName,
cIscsiSsnTsih,
cIscsiSsnIsid,
cIscsiSsnInitiatorAlias,
cIscsiSsnTargetAlias,
cIscsiSsnInitialR2T,
cIscsiSsnBidiInitialR2T,
cIscsiSsnImmediateData,
cIscsiSsnType,
cIscsiSsnMaxOutstandingR2T,
cIscsiSsnFirstBurstSize,
cIscsiSsnMaxBurstSize,
cIscsiSsnConnectionNumber,
cIscsiSsnAuthIdentity,
cIscsiSsnDataSequenceInOrder,
cIscsiSsnDataPduInOrder,
cIscsiSsnErrorRecoveryLevel
}STATUScurrentDESCRIPTION"A collection of objects providing information applicable to
all sessions."::={ cIscsiGroups 15}cIscsiSessionStatsGroup OBJECT-GROUPOBJECTS{
cIscsiSsnCmdPdus,
cIscsiSsnRspPdus,
cIscsiSsnTxDataOctets,
cIscsiSsnRxDataOctets
}STATUScurrent
DESCRIPTION"A collection of objects providing information about message
and data traffic for all sessions."::={ cIscsiGroups 16}cIscsiSessionCxnErrorStatsGroup OBJECT-GROUPOBJECTS{
cIscsiSsnDigestErrors,
cIscsiSsnCxnTimeoutErrors
}STATUScurrentDESCRIPTION"A collection of objects providing information about connection
errors for all sessions."::={ cIscsiGroups 17}cIscsiConnectionAttributesGroup OBJECT-GROUPOBJECTS{
cIscsiCxnCid,
cIscsiCxnState,
cIscsiCxnProtocol,
cIscsiCxnLocalAddrType,
cIscsiCxnLocalAddr,
cIscsiCxnLocalPort,
cIscsiCxnRemoteAddrType,
cIscsiCxnRemoteAddr,
cIscsiCxnRemotePort,
cIscsiCxnMaxRecvDataSegLength,
cIscsiCxnHeaderIntegrity,
cIscsiCxnDataIntegrity,
cIscsiCxnRecvMarker,
cIscsiCxnSendMarker
}STATUScurrentDESCRIPTION"A collection of objects providing information about all
connections used by all sessions."::={ cIscsiGroups 18}
cIscsiTgtLgnNotificationsGroup NOTIFICATION-GROUPNOTIFICATIONS{
cIscsiTgtLoginFailure
}STATUScurrentDESCRIPTION"A collection of notifications which indicate a login
failure from a remote initiator to a local target."::={ cIscsiGroups 19}cIscsiIntrLgnNotificationsGroup NOTIFICATION-GROUPNOTIFICATIONS{
cIscsiIntrLoginFailure
}STATUScurrentDESCRIPTION"A collection of notifications which indicate a login
failure from a local initiator to a remote target."::={ cIscsiGroups 20}cIscsiSsnFlrNotificationsGroup NOTIFICATION-GROUPNOTIFICATIONS{
cIscsiInstSessionFailure
}STATUScurrentDESCRIPTION"A collection of notifications which indicate session
failures occurring after login."::={ cIscsiGroups 21}cIscsiCompliances OBJECTIDENTIFIER::={ cIscsiConformance 2}cIscsiComplianceV1 MODULE-COMPLIANCESTATUScurrentDESCRIPTION
"Initial version of compliance statement based on
initial version of MIB.
If an implementation can be both a target and an
initiator, all groups are mandatory."MODULE-- this moduleMANDATORY-GROUPS{
cIscsiInstanceAttributesGroup,
cIscsiPortalAttributesGroup,
cIscsiNodeAttributesGroup,
cIscsiSessionAttributesGroup,
cIscsiSessionStatsGroup,
cIscsiSessionCxnErrorStatsGroup,
cIscsiConnectionAttributesGroup,
cIscsiSsnFlrNotificationsGroup,
cIscsiInstanceSsnErrorStatsGroup
}-- Conditionally mandatory groups to be included with-- the mandatory groups when the implementation has-- iSCSI target facilities.GROUP cIscsiTgtPortalAttributesGroup
DESCRIPTION"This group is mandatory for all iSCSI implementations
that have iSCSI target facilities."GROUP cIscsiTargetAttributesGroup
DESCRIPTION"This group is mandatory for all iSCSI implementations
that have iSCSI target facilities."GROUP cIscsiTargetLoginStatsGroup
DESCRIPTION"This group is mandatory for all iSCSI implementations
that have iSCSI target facilities."GROUP cIscsiTargetLogoutStatsGroup
DESCRIPTION"This group is mandatory for all iSCSI implementations
that have iSCSI target facilities."GROUP cIscsiTgtLgnNotificationsGroup
DESCRIPTION"This group is mandatory for all iSCSI implementations
that have iSCSI target facilities."GROUP cIscsiTargetAuthGroup
DESCRIPTION"This group is mandatory for all iSCSI implementations
that have iSCSI target facilities."-- Conditionally mandatory groups to be included with-- the mandatory groups when the implementation has-- iSCSI initiator facilities.GROUP cIscsiIntrPortalAttributesGroup
DESCRIPTION"This group is mandatory for all iSCSI implementations
that have iSCSI initiator facilities."GROUP cIscsiInitiatorAttributesGroup
DESCRIPTION"This group is mandatory for all iSCSI implementations
that have iSCSI initiator facilities."GROUP cIscsiInitiatorLoginStatsGroup
DESCRIPTION"This group is mandatory for all iSCSI implementations
that have iSCSI initiator facilities."GROUP cIscsiInitiatorLogoutStatsGroup
DESCRIPTION"This group is mandatory for all iSCSI implementations
that have iSCSI initiator facilities."GROUP cIscsiIntrLgnNotificationsGroup
DESCRIPTION"This group is mandatory for all iSCSI implementations
that have iSCSI initiator facilities."GROUP cIscsiInitiatorAuthGroup
DESCRIPTION"This group is mandatory for all iSCSI implementations
that have iSCSI initiator facilities."::={ cIscsiCompliances 1}
END